2006 Mazda 5 Haynes Manual
Access your Mazda 5 2006 Owner's Manual Online Mazda 5 Owners Manual 2006. Mazda 5 (2005 - 2010). We have created thousands of new videos, for hundreds of popular cars, including the Mazda 5 2005 - 2010. All come with the Haynes.
Auto Facts offers service repair manuals for your Mazda 3 - DOWNLOAD your manual now!
. P/N: 0000-8F-Z01 P/N: 0000-8F-F05 P/N: 0000-8F-Z02 P/N: 0000-8F-Z10 P/N: 0000-8F-L06 MAZDA GENUINE ACCESSORIES WARNING: / AVERTISSEMENT Vehicle Remote Start System This vehicle is equipped with a remote controlled engine starter. To reduce the risk of serious Injury or death, switch engine starter Owner's Manual 2 sec.
VEHICLE PREPARATION, continued 2. History teachers manual bju. Remove the following components: a.
Using a fiber stick remove the driver’s side scuff plate. Remove the driver’s side kick panel by using a fiber stick FIGURE B pull the plastic center button of the plastic fastener out to dis- engage (FIGURE B). DIPOLE ANTENNA MOUNTING 1.
Remove the following components a. Remove the driver’s side A-pillar panel being careful not to damage the retaining clips or the curtain airbag. Care- fully pull the rubber weather seal away from the door jamb (FIGURE J) then, starting at the top of the panel, pull the A-pillar panel toward the inside of the car but DO NOT try to pull all the way off. HOOD SAFETY SWITCH MOUNTING 1. Using (2) supplied 1/4” self drilling screws and (2) supplied lock washers, secure the hood safety switch to the drivers side of the vehicle’s hood 150mm above the top of the hood mounting bracket and 85mm from the side edge of the hood. HOOD SAFETY SWITCH MOUNTING, continued 5. Locate the hood release cable grommet from inside the occupant compartment.
(FIGURE U) 6. Pull the hood release cable and grommet approximately 20” into the driver’s side footwell. (FIGURE V) 7. Using fish wire, pull the hood safety switch wiring through the hood release cable opening: a. REMOTE START CONTROL MODULE PREPARATION 1. Insert the supplied fuses into the remote start control module as shown in below (FIGURE Z). The fuses fit tight so use a tool handle to seat them in place if necessary.
Install DNA card into the remote start control module as shown below. (FIGURE AA) NOTE: Use care to assure that both rows of the multipin connectors are aligned and seated properly. HOOD SAFETY SWITCH MOUNTING WIRE CONNECTIONS 1.
Locate the BLACK/ORANGE and GRAY/RED wire from the remote start system harness. Locate the wires listed below. If the hood safety switch wire has a ground ringlet terminal or a stripped end on either wire then cut the ends of the wires so they are blunt. 1030658 Rev.A 09/05. IMMOBILIZER INTERFACE RIBBON CABLE MOUNTING 1. Route the immobilizer interface (previously installed) ribbon cable to the ignition switch, making sure to keep it away from any moving parts. Following the instructions on the supplied ampule of adhesive primer, apply a thin coating to the entire transceiver antenna ring (black plastic ring around key switch, FIGURE GG) and to the ribbon cable.
WIRE HARNESS CONNECTIONS- STEERING COLUMN MULTIFUNCTION SWITCH CONNECTOR (C-459 CONNECTOR) 1. Locate the 12-way WHITE multifunction switch connector on the left side of the steering column (plugged into the turn signal assembly). Remove the 12-way connector from the multifunction switch. WIRE HARNESS CONNECTIONS- BRAKE SAFETY 1.
Locate the wire harness running along the firewall on the left side of the steering column near the hood release cable (directly in front of the module mounting location). (FIGURE QQ) 2. Locate the wire GREEN/YELLOW brake switch wire. NOTE: There will be only (1) GREEN/YELLOW wire in this harness. RE-ASSEMBLY 1.
Re-install the following components: a. Plug the ignition key light back into the lower steering column shroud, carefully snap the steering column shroud halves together and re-install the (3) phillips screws (all three are the same type). Verify operation of the tilt/tele- FIGURE SS scoping steering wheel.
SYSTEM POWER-UP 1. Verify that all connections are secure as per installation instructions. Turn the ignition key to the RUN position. Reconnect the negative battery terminal. Turn the ignition key to the OFF position.
VERY IMPORTANT - USING THE IGNITION KEY, TURN THE IGNITION TO THE ON POSITION THEN CRANK ENGINE UNTIL IT STARTS ONE TIME THEN SHUT THE VEHICLE OFF. FUNCTION TEST Car Find 1. Press and hold START button - Horn should beep five times and parking lights should flash five times. Remote Engine Start Functions 1. REMOTE ENGINE START; Make sure the key is removed from the ignition switch and the engine hood is closed.
HOOD SAFETY SWITCH ADJUSTMENT The hood safety will need to be adjusted to shutdown the vehicle when the hood is raised to the full upright position 1. Raise and prop the vehicle’s hood. The hood switch cylinder should be bend away from the hood to approximately 15 degrees above parallel with the ground. 1030658 Rev.A 09/05. ATTENTION: Installation Instruction change for P/N 0000-8F-L05B The Fuse placement position changed for REMOTE START SYSTEMS on all Mazda 5 vehicles. 2008 AND NEWER.
The Dome Light Fuse must be placed in the positive position in order to disarm the Factory perimeter alarm during the remote start sequence. ® GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS ADDENDUM APPLICABLE MODELS: PART NUMBER (s): TACHOMETER CONNECTION 2006-08 MAZDA 5 0000-8F-L05B SUPPLEMENT WIRE HARNESS CONNECTION TACH WIRE CONNECTION TO VEHICLE 1. Locate the WHITE 56” Tach wire in the remote start wire harness. This wire is covered with black shrink wrap for protection against moisture and heat when routing in the engine compartment. The horn will beep 4 times, indicating that the system has learned the current idle rate. Release the brake pedal.
2006 Mazda 5 Blower Motor Removal
Turn the ignition key to the OFF position. Proceed to Step 15 of the Mazda 5 Installation Instruction Manual to continue programming. TROUBLESHOOTING GUIDE 1.
2006 Mazda 5 Rear Suspension Diagram
Horn honks 4 times & vehicle does not start - No tachometer signal learned to DNA card. Ensure good connection and correct vehicle wire at PCM (See Step 1). Re-program tachometer signal (See Step 3).