Rigging Guide Queensland
. Modification History Not Applicable Unit Descriptor Unit descriptor This unit specifies the outcomes required to perform rigging work at the intermediate level, which includes all the outcomes for rigging work at the basic level, and also includes rigging of cranes, rigging of conveyors, rigging of dredges and excavators, rigging associated with tilt slabs, rigging associated with demolition work, and dual lifts for licensing purposes.
Information on dogging and rigging and the areas of concern. Rigging Guide Queensland pdf, in that dispute you approaching on to the fair site. We move Rigging Guide Queensland DjVu, PDF, ePub, txt, doctor appearing.
Application of the Unit Application of the unit This unit requires the applicant to be able plan the work, select and inspect equipment, set up task, erect structures and plant and dismantle structures and plant. This unit is based upon the National Standard for Licensing Persons Performing High Risk Work. This unit in its current form meets state and territory licensing requirements. Any alteration will result in a unit which is not acceptable to regulators for the purpose of licensing. This unit has a pre-requisite requirement.
This requirement may be met by either the successful completion of the unit CPCCLRG3001A Licence to perform rigging basic level or holding a valid licence for basic rigging. Licensing/Regulatory Information Refer to Unit Descriptor Pre-Requisites Prerequisite units CPCCLRG3001A Licence to perform rigging basic level Employability Skills Information Employability skills This unit contains employability skills. Elements and Performance Criteria Pre-Content Elements describe the essential outcomes of a unit of competency. Performance criteria describe the performance needed to demonstrate achievement of the element. Where bold italicised text is used, further information is detailed in the required skills and knowledge section and the range statement. Assessment of performance is to be consistent with the evidence guide.
Elements and Performance Criteria ELEMENT PERFORMANCE CRITERIA 1. Task to be undertaken is assessed 1.2. Potential workplace hazards are identified 1.3. Hazard control measures are identified consistent with appropriate standards to ensure the safety of personnel and equipment 1.4. Site information is obtained 1.5. All forces and loads associated with erecting and dismantling structures and associated plant are considered in consultation with appropriate personnel. Rigging equipment and associated equipment are identified in consultation with appropriate personnel according to procedures and site information.
Safety equipment is identified. Appropriate communication methods are identified with appropriate personnel. Select and inspect equipment. Rigging equipment and associated equipment are selected and inspected according to procedures and the appropriate standard. Safety equipment is selected and inspected according to procedures. All defective rigging equipment, associated equipment and safety equipment is isolated, reported and recorded according to procedures.
Communication equipment is selected and inspected for serviceability (where applicable) 3. Set up tasks. Appropriate hazard prevention / control measures are applied to the work area according to procedures. Ground suitability is inspected and checked (where appropriate). Site information is reviewed, interpreted and communicated to appropriate personnel and appropriate personnel.
All forces and loads associated with erecting and dismantling structures and associated plant are determined in consultation with appropriate personnel. Safety equipment is fitted and worn correctly (where appropriate). Rigging equipment and associated plant are positioned for work application and stability according to procedures. Erect structures and plant. Structures and associated plant is erected according to procedures and site information. Stability of structures and associated plant is maintained during erection according to procedures.
Work is conducted safely at heights including safe and effective use of safety equipment. Appropriate communication methods and communication equipment, are used to co-ordinate the tasks. Temporary guys, ties, propping and shoring, including flexible steel wire rope, and tubing, are connected where required.
Wire Rope Rigging Guide
Associated plant and rigging equipment is used according to procedures and the appropriate standard. Associated equipment is used in a safe and appropriate manner. The completed task is inspected according to the appropriate standard. Excess materials are removed from the work area (where applicable) 5.
Dismantle structures and plant. Structures and associated plant are dismantled according to procedures and the appropriate standard. Work is conducted safely at heights including safe and effective use of safety equipment. Stability of structures and associated plant is maintained during dismantling according to procedures. Rigging equipment, associated equipment, safety equipment and associated plant are inspected for damage and defects 5.5. All defective rigging equipment, associated equipment, associated plant and safety equipment are isolated reported and recorded according to procedures.
Rigging equipment and associated equipment are stored according to procedures and the appropriate standard. Hazard prevention/control measures are removed (where appropriate) Required Skills and Knowledge REQUIRED SKILLS AND KNOWLEDGE This section describes the skills and knowledge required for this unit. Required skills Required skills for this unit are:. ability to calculate Safe Working Load (SWL) and Working Load Limit (WLL). ability to erect and dismantle, level, plumb and stabilise associated plant and structures. ability to work safely at heights including the correct application of safety equipment. accurate interpretation of structural charts and structural plans (site information).
correct application and use of all rigging and associated equipment. risk assessment and hazard control strategies. interpersonal and communication skills at a level sufficient to site/workplace requirements. This includes the relevant communication methods and equipment.
verify problems and equipment faults and demonstrate appropriate response. Training component details The following details are displayed for each different NRT:- Training packages - Training package details - Training package components Qualifications - Qualification details - Qualification components Accredited courses - Accredited course details Modules - Module details Units of competency - Units of competency details - Unit components Skill sets - Skill set details - Skill set components Click on the Export link to export the NRT information to MS Word or PDF. Click on the Manage notification link to create or change a notification for this NRT.
When selecting the Display history check box a set of tables will appear displaying a log of historical values describing what has changed and when over time. If you have access to make changes to an NRT, click on the Edit link on the upper right hand side of the summary box.
No information is available for this page.Learn why. Find great deals on eBay for Owners Manual Case in Other Models. Shop with confidence. Manual case erector. Find great deals on eBay for Case Tractor Manual in Antique & Vintage Manuals. Shop with confidence. Sep 30, 2017 - This is the Highly Detailed factory service repair manual for theCASE IH MAXXUM 125 TRACTOR, this Service Manual has detailed. Backed by CNH Parts & Service, only your Case IH dealer has what it takes to. Find and order operator's manuals, service manuals and other technical.